A: HTV Anything will always be your bottom or base layer. Think of HTV Anything as your T-shirt that your are pressing your heat transfer vinyl too. You are just turning your HTV into a dishwasher safe sticker or decal. You also press to the SHINY side.

Here is a heat pressing example:
You are making a custom glitter name to go on a tumbler with HTV Anything, Hot Pink Glitter HTV, and White Glitter HTV.

Step 1: Press the White Glitter HTV to the HTV Anything material at 315 Degrees for 3-4 Seconds.

Step 2: Press the Hot Pink Glitter HTV to the White Glitter HTV at 315 Degrees for 8-10 Seconds.

Step 3: You decal is now completed. When ready to apply you will just remove the back carrier sheet of the HTV Anything Material to expose the Adhesive and apply to your smooth flat surface.

A: For the HTV Anything on the Cricut Maker I use these custom settings in Design Space:

Cut Pressure: 240
Multi Cut: Off
Blade: Fine Point Blade

When cutting the HTV Anything you want to create a offset or Contour of the Heat Transfer Vinyl Design to make it easier to line up correctly. I normally do about a .06" Offset with the HTV Anything

A: HTV Anything is a unique material that The Rhinestone World manufactures to turn regular heat transfer vinyls into a dishwasher safe sticker/decal. So you can use a product like a beautiful Siser Glitter HTV that you would normally use for t-shirts and heat press it to the HTV Anything material to make a custom decal. You can also layer the Glitter HTV as much as you would like to have multiple colors. The HTV Anything material has a special adhesive on the back to then apply it to any smooth flat surface you would like for your customers. Examples are Tumblers, Cups, Cell Phones, TV's, Walls, Windows, and much more.

A: Our best results are:
Depth 6
Force 28
Speed 10
Passes 2

Remember to always do test cuts as the life of your blade can impact your cuts.

A: Great question! No, you cannot press rhinestones directly to HTV Anything. Instead, you can press rhinestones directly to our Bling Anything decal material.

A: Our Award Winning ColorSpark HTV Anything turns HTV (heat transfer vinyl) into a decal.

To use this, we recommend using a Teflon sheet rather than parchment paper to protect the decal material as well as your heatpress or Easypress. You will sandwich the HTV Anything inside a sheet of teflon. The order goes: teflon on bottom, HTV Anything material, htv, then teflon sheet on top to fully protect your decal material. You treat the HTV Anything as you would if you were pressing htv to a shirt. Press to the SHINY side and align your htv. Trim the carrier sheet of your htv close to your designs so you do not have any carrier sheet touching the edges of your HTV Anything. Cover with Teflon and press for about 8 seconds. Open your Teflon "sandwhich" and peel the carrier sheet from your htv. You can break the typical pressing rules by layering glitter htv on top of glitter htv and even rhinestones on top of glitter htv when making a decal with our HTV Anything. After you have pressed all layers, trim the HTV Anything CLOSE to the htv but do not cut right to the edge of your htv. Peel the papery backing and apply your new decal to a hard, nonporous surface. Your decal is dishwasher safe and even car wash/weather safe. Please note, HTV is not rated for extended outdoor use, so htv decals will fade in the sun over time.

A: No, you do not have to seal it with anything. The adhesive we use on the back of the HTV Anything is strong enough to hold through the dishwashing cycle. Make sure the tumbler or cup is also dishwasher safe as well.

A: That is the amazing part about the HTV Anything Material. Your tumbler or product is never exposed to any heat. You are heat pressing the t-shirt HTV directly to the HTV Anything material to make a adhesive decal. You can then apply that decal to any smooth flat surface like a tumbler or mug for your finished product.

A: The HTV Anything does not get mirrored as the adhesive is on the side next to the backing sheet, just like adhesive vinyl. You will have the SHINY side UP, just like decal material. When cutting any new material, remember there are several factors that go into getting a nice, clean cut: Life of your blade, individual machine capability as well as it's calibration, cut strip or cutting mat lifetime. With all of these factors to consider, we kindly ask all users to do test cuts before cutting a large project. We have set custom settings on our Cricut for this material, which are: 240 pressure, single cut. Please use this as a starting point to dial in proper cutting pressure depending on your blade and the other factors mentioned above.

A: First, I apologize for any confusion you may have had trying to use your HTV Anything decal material.

There are a few rules to keep in mind when using HTV Anything:

Always press to the SHINY side.
Make sure the carrier sheet of your htv is smaller than your piece of HTV Anything. The sticky carrier can pull up the edges of your HTV Anything and ruin your decal.

For HTV Anything, you can either add a Contour (Do Not Mirror!) to your design in your software and cut the Contour with your vinyl cutter before pressing HTV to it. OR if you'd rather trim with scissors, you can press htv to the HTV Anything and trim the excess HTV Anything after it's pressed. Again, make sure your htv carrier sheet is not near the edges of your HTV Anything--you can trim your htv carrier sheet close to your design before pressing.

HTV Anything does not get mirrored when you cut it with your vinyl cutter.
The adhesive is on the back of the material and you are pressing to the shiny side, which melts a bit to help adhere your htv to this decal material. Sometimes, it may help to think of the HTV Anything as you would a shirt you're decorating with HTV. Just place the HTV Anything Shiny Side UP, align your HTV to it, cover with Teflon and press. If you are doing a single color decal, press 6-8 seconds at 300 degrees F. If you are layering htv, press the first layers 2-3 seconds, peel the htv carrier sheet, align the next layer and re-cover with Teflon and press. Final layer gets the full 6-8 dwell time. If you are layering hotfix Rhinestones on top of HTV, after the 6-8 second final press of htv, align your Rhinestones to the htv, again, making sure the sticky Acrylic Hotfix Tape is not touching the edges of your HTV Anything, and press 15 seconds at 315-320 degrees. HTV Anything and the Teflon sheet tend to hold heat and we recommend letting the transfer cool a bit before removing the Acrylic Hotfix Transfer tape, just to allow the rhinestone adhesive to cool a bit and fully adhere to the htv underneath.

Use a smooth Teflon sheet when creating decals using HTV Anything.
The HTV Anything can melt to your heated platen, Easypress or iron, so the Teflon sheet is important. If you use a textured Teflon sheet, the texture will show up in your clear HTV Anything decal material.

Our first run of HTV Anything had a protective cover sheet on it that needed to be removed prior to pressing or cutting. We found issues with the cover sheet and have had all other batches made without the cover sheet.

*Please remember, using HTV Anything allows you to 'break' some of the traditional rules of decorating that you would normally use for apparel. You can layer glitter on glitter and even hotfix rhinestones on glitter htv ONLY when using our HTV Anything (or Bling Anything) decal materials. You cannot layer these items for decorating apparel.

A: Yes, you can!

A: Great question! ColorSpark HTV Anything is the product we are using to decorate the Maars skinny acrylic cups. Our ColorSpark HTV Anything can turn htv into a dishwasher safe decal. If using rhinestones, please be sure to have htv as your bottom layer and do not try to press rhinestones directly to HTV Anything.

A: Of course! Our ColorSpark HTV Anything is a unique material that turns your heat applied htv into a dishwasher safe decal. You can even layer multiple colors of htv on each other and break a few of the typical pressing rules we'd use for apparel. Example: You can layer glitter htv on top of glitter htv when making a decal! You can also layer hotfix rhinestones over your glitter htv on decals.

To use the HTV Anything, you will be using a Teflon sheet and make a "teflon sandwich" when you press. Open your Teflon sheet and place it on your lower platen of your heat press. You can also use a Cricut Easypress with this material. Place your HTV Anything SHINY side up on your Teflon and align your htv on top. Trim the carrier sheet close to your design as the sticky carrier can pull up the edges of the HTV Anything. Close your 'Teflon sandwich' and press according to the pressing specs of the material you are using. You can shorten the dwell time to about 8-10 seconds. If this is your final color or layer, flip the teflon sandwich over and press an additional 5-8 seconds from the back. You are getting the heat directly to the adhesive of your htv to ensure it is well adhered to your HTV Anything deal materail. Open the teflon sandwich and carefully peel the carrier sheet. As mentioned, you can layer more colors on top of the base color of htv or even layer rhinestones on top of your htv. Please note that rhinestones cannot adhere directly to the htv anything, but need a layer of htv under them for these decals.

A: Yes it can! It is guaranteed to last 7-8 years.

A: You can cut it with any craft cutter or scissors.

A: For cups, Bling Anything will work great. If you want to use ONLY rhinestones on a design, Bling Anything is the material needed. HTV Anything is a bit less expensive because it is designed to not have the layer that will hold the rhinestones by themselves.

A: We have applied decals made with our HTV Anything and tested them in the dishwasher same day. This is another advantage to using HTV and HTV Anything over adhesive/decal vinyl on items that will be going in the dishwasher.

A: You do not need Vinyl Shield over our HTV Anything ot our Bling Anything materials.

A: Unfortunately, no. Foil will stick to the entire surface of HTV Anything.

A: Is your tumbler preserved/slightly textured, by chance? In our testing, HTV Anything sticks best to smooth surfaces.

If, however, your tumbler is a smooth surface, always clean the surface with alcohol before applying decals or HTV Anything. Firmly press with your thumbs as you apply the HTV Anything, as the pressure will give you a better bond. Also, as the HTV Anything is allowed to set up, the bond becomes stronger with time.

A: The adhesive we use on the HTV Anything is incredibly strong. The layers the htv gets pressed to also have components in the design and manufacture that keep your htv from lifting after use or going through the dishwasher.

A: The white backing should be facing down on the matt, the clear sheet on top is what you're actually cutting.

A: You can press holographic HTV to it, just be aware that you may have issues with bubbling or rippling after pressing. HTV Anything works best with thinker vinyl's like glitter, but thinner HTV's like holographic will stick too.

A: It would stick but we do not recommend it, pressing material that thin to HTV anything is going to be very tricky and you're more than likely going to have issues with bubbling and rippling.

A: Hi there! The HTV Anything had started off with that thin layer, but we have since had it manufactured without the extra layer. We have been adding labels with instructions to remove the cover sheet on the rolls that had the cover sheet.

A: Great question! While both our Bling Anything material and HTV Anything material turn heat applied materials into decals that are dishwasher safe, the main difference is what you can/should apply directly to them. The clue is found in the name of the material. With BLING Anything, you can apply hotfix rhinestones directly to it. With HTV Anything, you apply HTV to it (first). On either one, you can layer rhinestones over the top of the htv. Our HTV Anything is thinner and can have thinner htv pressed to it, but you will want to take some precautions, such as taping down your htv to help prevent any bubbling. When removing your carrier sheet, roll it off rather than pulling up vertically. Taking these precautions will help ensure any thinner materials you apply to htv anything will garner great results.

A: Epoxy isn’t needed with our Award Winning HTV Anything. The decals you can make are completely dishwasher safe. If you choose to use epoxy over the top, it would work like any layered decal you’d use under epoxy.

A: Unfortunately we do not have a distributor in Australia, all of our products ship from our main facility in the USA.

A: Unfortunately we do not recommend sublimating to straight to HTV anything.

A: That's a great question!

You can either create a contour of your design in your software and cut that contour in your HTV Anything. Do NOT mirror this contour. Cut HTV Anything SHINY side up. Weed off the excess. Then align your htv design, cover with Teflon and press your htv to the HTV Anything. Always make sure the sticky carrier sheet for your htv is trimmed close to your design before pressing and don't have your design too close to the edge of your HTV Anything, as the sticky carrier can pull up the edge of your decal when you remove the htv carrier.

OR

You can align your htv to the SHINY side of your HTV Anything, Cover with Teflon before pressing. Again, don't have the edge of your htv carrier near the edge of your HTV Anything. Trim the excess HTV Anything with scissors after pressing.

Press initial layers of htv 2-3 seconds at 300 degrees F. Final layer of htv press 6-8 seconds. Remember to remove the carrier sheets of your htv between layers.

Remove the Teflon sheet and after peeling the plasticy/paper backing, your decal is ready to stick to a hard, non-porous surface.

A: We have had great success with both HTV Anything and Bling Anything decals adhering to powder coated tumblers.

Our temperature color changing adhesive vinyls have an incredibly strong adhesive and have also held up very well on the matte black Maars tumblers, which have a similar texture.

A: Hi there! Yes, you can use HTV Anything on any smooth, hard surface. While it'd even stick and wear well on car windows, htv itself isn't rated for outdoor use and would fade. But this shows how durable decals made with our HTV Anything can be!

While we have not tested it ourselves ,we have heard from customers who have even subbed directly to the HTV Anything.

From our understanding, Sublimation Mugs tend to be more pricey than regular mugs. You'll likely have less cost involved using the HTV Anything on regular mugs, but it will stick fine to your sub mugs.

A: We have an order en route, but shipping sometimes gets delayed, which prolongs the timing of when we will have it in. Please keep checking back, as it could sell out again, once we've restocked.

A: Our Award Winning HTV Anything turns HTV (heat transfer vinyl) into a dishwasher safe decal. We recommend using a heatpress or Easypress to apply the htv (Iron on vinyl) to the HTV Anything. Using a teflon sheet, place your HTV Anything shiny side up on the teflon. Place your htv adhesive side down on top of the HTV Anything, making sure your carrier sheet is not near any of the edges of your HTV Anything. (The carrier sheet is sticky enough to pull up the edges of the HTV Anything when you remove the carrier.) Cover with the rest of your Teflon sheet and press. If you want to layer multiple colors of HTV for your decal, please remember to remove the carrier sheet in-between layers. ;)

A: HTV Anything and Bling Anything both can be used to decorate tumblers. The difference between the two materials is that when using ONLY Hotfix rhinestones in a design, you must use Bling Anything. Rhinestones cannot be pressed directly to HTV Anything.

A: HTV Anything is our decal material that turns heat transfer vinyl into a dishwasher safe decal. The only time you would use Rhinestones with this product is if you are layering hotfix rhinestones on top of your htv to create a decal. This material does not go on apparel. Our Bling Anything sheets are a different product which have 18,000 ss06 machine cut rhinestones imbedded in an adhesive backed material, which can be cut and applied to hard, non-porous surfaces. That product does not require a heat press and also is not used for apparel.

A: To safely cut HTV or similar materials with a laser, you will need HTV that is CPSIA certified. This material has not been CPSIA certified, so we do not recommend cutting it with a laser. However, ColorSpark HTV Anything cuts easily with a Cameo or Cricut or other vinyl cutter using a blade.

A: Close. We have two clear products to turn heat applied materials into a decal. The clue to what products used on each decal material is in its name. BLING ANYTHING can have Rhinestones presses directly to it. HTV ANYTHING turns htv into a decal. You can layer rhinestones on the htv after the htv has been pressed to the HTV ANYTHING decal material.

A: Many things can affect your cuts, ranging from blade life, mat life, calibration of your specific machine. We encourage you to do test cuts on any material, but especially for material that is new to you. For the HTV Anything on the Cricut Maker I use these custom settings in Design Space:

Cut Pressure: 240
Multi Cut: Off
Blade: Fine Point Blade

Please use these as a starting point, do a test cut and adjust up or down with the pressure to ensure your cuts are perfect.

When cutting the HTV Anything you want to create a offset or Contour of the Heat Transfer Vinyl Design to make it easier to line up correctly. I normally do about a .06" Offset with the HTV Anything

A: 1- You should use the light cardstock setting, for more details about recommended cut settings please see the link below.
https://www.therhinestoneworld.com/cut-settings
2- You're cutting the side with the clear plastic layer, the milky white sheet is the backing, If you peel up the corner you should notice that the clear sheet has an adhesive backing as well.
3- The pressing order is the same as pressing HTV to any garment, but pressing to the clear side of the HTV anything instead. When you're ready to apply after pressing, peel off the white backing and stick it to a smooth flat surface.

A: We normally only recommend sticking it to smooth, flat surfaces. Depending on how rough the texture is on the cup you may have issues with adhesion.

A: Yes, Siser brick is fine to use with HTV anything.

A: You can find all of the pressing temperatures and times at the link below.
https://www.therhinestoneworld.com/Rhinestone-Vinyl-Pressing-Specs

A: If you are creating a Contour in your software for the HTV Anything portion, do NOT mirror the contour...think of the HTV Anything like you would decal vinyl, but you're able to press htv to it.

You will still mirror your htv design and weed as normal. When pressing, please trim your htv carrier sheet close to the design so that it does not touch the edges of your HTV Anything. The sticky carrier can pull up the edges of the HTV Anything and ruin your decal.

Our first run of HTV Anything (made in the summer of 2020) had a protective cover sheet on it that needed to be removed prior to pressing or cutting. We found issues with the cover sheet and have had all other batches made without the cover sheet.

A: We have an order en route and hope it will arrive soon. Unfortunately, shipping delays have caused a slight delay and we cannot guarantee the date it will be in stock at the warehouse. It's very popular and could sell out quickly, so please keep checking back to be sure you are able to order it when it is restocked.

A: The longer an HTV Anything decal is left to bond with whatever you apply it to, the stronger the bond will be. You can peel it off, however, the adhesive will be very compromised and likely won't adhere very well if you attempt to move it unless it's within a few seconds of applying.

HTV Anything decals need to be stuck to hard, non-porous surfaces.

A: This product is meant to be used as an adhesive backing for HTV, not go on top of the HTV applied to the tumbler.

If you are looking for a protective layer for thinner vinyls, you can try our ColorSpark Vinyl Shield. Our ColorSpark Vinyl Shield cannot go on top of textured vinyls, so we would not recommend using it over glitter in lieu of epoxy.

A: Yes, but we recommend a thicker vinyl such as brick or glitter so you do not have issues with wrinkling/warping, which you may experience with normal thin HTV's.

A: While our HTV Anything does turn htv into decals that are dishwasher safe and have stayed on car windows for years, htv is not rated for outdoor use and tends to fade within months.

We recommend you look out our ColorSpark Adhesive vinyls for outdoor use. The Permanent vinyls are rated for 3-5 years outdoors. Our ColorSpark Reflective adhesive vinyls are also rated 3-5 years outdoors, have brilliant color and a great reflective property at night when light hits them.

A: Yes, we ship worldwide. The exception is equipment and the Magic Vinyl Remover.

A: HTV Anything is meant to go on hard, nonporous surfaces. While it may adhere to a soft-sided cooler or material for a bit, it likely would be temporary and not how we would recommend using this product.

A: Envíos internacionales funcionan igual de la manera de envíos normales ya que vayas a terminar tu orden te van a salir todo los diferentes métodos que tienes de envio y cuanto cuestan dependiendo pues el peso y adonde vaya.

A: As long as it is not overly textured the HTV anything will stick, but in this case I would probably recommend hand washing, as textured tumblers can cause problems with adhesion.

A: We have a great Resources section at the bottom of every TRW page. Under the Frequently Asked Questions section, we have a blog titled, “I just got my HTV Anything, how do I use it?”

There are a few rules to keep in mind when using HTV Anything:

Always press to the SHINY side.
Make sure the carrier sheet of your htv is smaller than your piece of HTV Anything. The sticky carrier can pull up the edges of your HTV Anything and ruin your decal.

For HTV Anything, you can either add a Contour (Do Not Mirror!) to your design in your software and cut the Contour with your vinyl cutter before pressing HTV to it. OR if you'd rather trim with scissors, you can press htv to the HTV Anything and trim the excess HTV Anything after it's pressed. Again, make sure your htv carrier sheet is not near the edges of your HTV Anything--you can trim your htv carrier sheet close to your design before pressing.

HTV Anything does not get mirrored when you cut it with your vinyl cutter.
The adhesive is on the back of the material and you are pressing to the shiny side, which melts a bit to help adhere your htv to this decal material. Sometimes, it may help to think of the HTV Anything as you would a shirt you're decorating with HTV. Just place the HTV Anything Shiny Side UP, align your HTV to it, cover with Teflon and press. If you are doing a single color decal, press 6-8 seconds at 300 degrees F. If you are layering htv, press the first layers 2-3 seconds, peel the htv carrier sheet, align the next layer and re-cover with Teflon and press. Final layer gets the full 6-8 dwell time. If you are layering hotfix Rhinestones on top of HTV, after the 6-8 second final press of htv, align your Rhinestones to the htv, again, making sure the sticky Acrylic Hotfix Tape is not touching the edges of your HTV Anything, and press 15 seconds at 315-320 degrees. HTV Anything and the Teflon sheet tend to hold heat and we recommend letting the transfer cool a bit before removing the Acrylic Hotfix Transfer tape, just to allow the rhinestone adhesive to cool a bit and fully adhere to the htv underneath.
Use a smooth Teflon sheet when creating decals using HTV Anything.
The HTV Anything can melt to your heated platen, Easypress or iron, so the Teflon sheet is important. If you use a textured Teflon sheet, the texture will show up in your clear HTV Anything decal material.

Our first run of HTV Anything had a protective cover sheet on it that needed to be removed prior to pressing or cutting. We found issues with the cover sheet and have had all other batches made without the cover sheet.

*Please remember, using HTV Anything allows you to 'break' some of the traditional rules of decorating that you would normally use for apparel. You can layer glitter on glitter and even hotfix rhinestones on glitter htv ONLY when using our HTV Anything (or Bling Anything) decal materials. You cannot layer these items for decorating apparel.

A: We do not have any suppliers in the UK but we do ship internationally. The pricing will vary depending on your exact location as well as the quantity you are buying. For a more accurate quote add the amount you are looking to purchase, proceed to checkout and fill out your shipping information, the site will generate you a shipping quote.

A: Hi there! Our recommenced Cut settings for ColorSpark HTV Anything are:

Blade: 3
Force: 20
Speed: 10

We do recommend test cuts as blade life and your own machine’s calibration can impact your cuts.

A: You can use a little bit of isopropyl alcohol to help loosen the adhesive, but please be aware that if there is any paint on the tumbler the alcohol may eat it away as well.

A: When using HTV Anything, only one layer of HTV Anything is needed and it will be your bottom layer. This is the material that turns your heat transfer vinyl into a decal that is dishwasher safe. The only time you should layer anything on top of glitter htv is when using our HTV Anything decal material as the bottom layer to stick your decal on a smooth, non-porous surface.

A: It depends on the type of vinyl you apply to HTV Anything, most commonly is Siser Glitter HTV. Which you may not want to apply vinyl shield to, as the textured surface would cause vinyl shield to have a hard time applying.

A: Yes we can ship to New Zealand, if you add the item to you r cart and proceed to checkout our system will generate a shipping quote for you.

A: They are not always interchangeable, we have a full video explaining the differences and uses for each below.

https://www.youtube.com/watch?v=sdWaEmQDJtY

A: No you cannot sublimate onto HTV Anything.

A: No you cannot sublimate onto HTV Anything.

A: We actually just posted some new videos on our blog that aim to help beginners learn about HTV anything, I have linked them below. If you need further assistance or have questions please reach out to our customer service team.

https://www.therhinestoneworld.com/Helpful-Videos-For-Working-With-HTV-Anything_b_227.html

Email: [email protected]
Phone: 941-755-1696

A: Bubbling can happen, especially with thinner vinyls such as easyweed, but here are a few things you can do to help prevent it. Press at a lower temperature, most vinyls press around 305F, so we recommend about 285F. Now after applying the vinyl, do not just pull up like you normally would to remove the HTV as this force can cause bubbling. Instead flip the decal over after pressing (transfer sheet facing down) and roll the HTV/HTV Anything off of the transfer sheet. If you need further assistance or have any questions please feel free to reach out to our customer service team via the info below.

Phone: 941-755-1696

Email: [email protected]

A: We have a blog post over this exact topic with a video explaining it.

https://www.therhinestoneworld.com/ColorSpark-Bling-Anything-vs-HTV-Anything-vs-Vinyl-Shield-Whats-the-Difference_b_158.html

A: We do not have a supplier located in the UK, but we do offer international shipping on most of our products. To get a shipping quote, please add the items to your cart, proceed to checkout, and fill out your shipping information. Our site will then generate you a quote based on your location and the order weight/size.

A: We normally recommend 300F for 6-8 sec, light/med pressure and cool peel.

A: As long as they are not overly textured, yes. The biggest thing about the adhesion is that the surface is smooth and flat.

A: I can't guarantee that we will be able to add another shipping method, but we will certainly take this feedback into consideration and see what we're able to do.

A: You can send them ready to apply! Just make sure they have a backing on the sticky side.

A: One roll of HTV Anything measures 12in wide by 5ft long, or 12in wide by approximately 1.66 yards.

A: They're actually very different! The Colorspark HTV Anything turns your HTV into a sticker. You would press your HTV to this material with heat (HTV on top, HTV Anything on bottom), and voila! You have your sticker. The Vinyl Shield goes over the top of your vinyl, acting as a shield, protecting it from scratches. We recommend the use of the product on dishwasher items, holographic vinyl, opal, and metallics.

A: No, we wouldn't recommend doing this with ANY vinyl materials, this one included.

A: This product turns your HTV (Heat Transfer Vinyl) into a decal, like a sticker! This wouldn't be necessary for adhesive vinyl, because it already has an adhesive backing. If you have further questions on this, please send us an email at [email protected], we're always happy to help!

A: Yes, it will work. Just be sure you protect your work by overcutting Vinyl Shield and placing securely over the top first.

A: Have you checked your press temp with a heat gun? If you're pressing for the correct time then try lowering your temp a touch.

A: It absolutely can!

A: You sure can! Have fun!!

A: Yes, the HTV Anything will work splendidly with Siser Glitter htv on a ceramic mug. Make sure your glitter carrier sheet is nowhere near the edges of your HTV Anything when you press, as it could pull up the edge and cause a bubble.

A: Always press to the SHINY side of HTV Anything. Keep your htv carrier away from the edges of the HTV Anything, as the sticky carrier can accidentally pull up the edge.

If you go to our FAQ page (under Resources at the bottom of every TRW Page), you can search HTV Anything. We have an extensive step by step tutorial to let you know everything needed to use this awesome material. Thanks!

A: Zero transfer tape is needed for HTV on shirts. You cut glossy side down with a mirrored image, then weed from the carrier that it's already on. Turn it over, glossy side up and place to the shirt then press.

A: As with any material you are cutting, we advise doing test cuts, to ensure your cut specs are dialed in properly. If your vinyl cutter has the option for a slower cut, that helps with getting details to cut well.

You may have a challenge aligning your weeded htv to our HTV Anything if they are tiny decals. A light board can help with that, but remember the Carrier sheet can’t be anywhere near the edges of your decal, as the sticky carrier can pull the edges up, creating wrinkles or bubbles.

One suggestion would be to press your htv Design to the HTV Anything and trim around the design with scissors after the decal has been pressed.

A: You can apply HTV Anything on any surface you'd like as long as it's smooth, clean and non textured.

A: When it comes to items HTV Anything will stick to, think of your HTV Anything the way you would a sticker. If a sticker would have a tough time sticking to a surface, your HTV Anything will also have a difficult time sticking. The properties of rubber and silicone materials and the way they are made makes any adhesive difficult to stick to them.

A: Here's one of our many amazing videos with all this info and more. https://www.youtube.com/watch?v=GGg5I8KRbKc&t=4s

A: We're based in Florida, USA and unfortunately shipping is our only option. Side not, we cannot ship chemicals or equipment, just for future ref. Thanks for the support!

A: Great question!
Bling Anything is our original decal material which turns heat applied materials into a decal or sticker. You can press either hotfix rhinestones directly to it or htv to it and even layer rhinestones on top of the htv.

HTV Anything is our newer decal material which is a bit thinner than Bling Anything as it lacks the extra layer which allows hotfix rhinestones to be pressed directly to it. You must press htv to it first and if you'd like to layer rhinestones on top of the htv, you can do that.

The name of the material lets you know what can be pressed directly to it. ;)
Bling Anything can take rhinestone directly pressed to it.
HTV Anything must have htv as the first layer pressed to it.

Decals made with either Bling Anything or HTV Anything can go through the dishwasher. They also can last on car windows, but htv is not rated for outdoor use and will fade quickly in the sun.

A: Yes, this is clear enough for wine glasses or car windows. Be sure to have your design away from the edge of the HTV Anything when you press it, as the carrier sheet from the htv can pull up the edge causing bubbles. We typically just trim close with a pair of scissors after pressing.
OR if we create a contour of the design first, we trim the htv carrier super close to the design before pressing. :)
Just so you know, Glitter htv can leave little glitter flakes in the open areas of the HTV Anything if you have a design with large open spaces between your htv.

A: Check the product on site under the tab Application Instructions found here: https://www.therhinestoneworld.com/colorspark-htv-anything

Please note these are recommended cut settings, we strongly suggest always making a test cut to ensure these cut settings work for you and your cutter. Setting can vary based on blade life, equipment, and material.
Silhouette Cameo 3, Cameo 4, and Cameo 4 Pro:
Blade depth: 3
Force: 20
Spped: 10
Passes: 1
Cricut Maker: 272
Circut Explore: Light cardstock

As for the layer order, yes, the HTV Anything will be your very back layer. To create a decal the HTV Anything is the sticky backed layer that will adhere to your tumbler so you'll layer HTV on top of that and press.
Offset your name, make the largest (back) layer the HTV Anything. Cut the name without the offset (mirror for HTV), this skinnier layer is your top layer with just HTV. Weed both, put the HTV on top of the HTV Anything, press.
Here's a great short video on the layer process: https://www.youtube.com/watch?v=qRr2rmwgw7s

A: HTV Anything is clear. Anything you leave exposed will show the background through, including the void. Hope that helps!

A: Our Headquarters and warehouse are in Florida, USA. Unfortunately, shipping is the only method available. We cannot ship chemicals or equipment.

A: ColorSpark HTV Anything Decal Material is a game changer for sticker lovers! Easily turn Heat Transfer Vinyl designs into peel and stick decals for customers or personal use.

ColorSpark HTV Anything is an exclusive, specialty material that turns regular heat transfer vinyl into dishwasher safe sticker decals.
HTV Anything can be cut with scissors or contour cut with a Craft-Cutter before the HTV is adhered to the HTV Anything material using a Heat-Press, easy-press or iron.
Finished decals can be applied to smooth, flat, hard surfaces such as cars, cups and electronics.
ColorSpark HTV Anything Decal Material is sold as a a 12” inch wide x 5 foot long roll.
Not sure what settings to use with your material? Check out our Recommended Cut Settings.


Have questions? Need craft ideas? TRW's blog has 100's of video tutorials, how-to guides, craft ideas, and expert tips for working with vinyl and rhinestones.

A: Yes, you can certainly only use one layer if you please

A: HTV Anything turns your HTV into a sticker essentially, so I wouldn't recommend it! The adhesive backing on this material wouldn't stick to your fabric long-term, as it is not a smooth, flat, nonporous surface.

A: Hi! Please email the help desk at [email protected] or call M-F 9-5 at: 941-755-1696 and we'll help work through the issue. Unfortunately we're based in Florida and have no stores overseas.

A: ColorSpark HTV Anything 5ft Roll -

The current coupon code from this video: https://www.youtube.com/watch?v=i1XgnUvzXVc

Is for 10% off Flatback stones, Flatback supplies and bling sheets: liveflatback10
Which also may be expiring soon if not already expired. Please make sure of the dates on videos to be sure they're not an old Live, and for fresh codes, join us Monday nights at 8pmEST on Youtube while we're live for trainings and give aways!

A: Nope! This decal material turns your HTV into a sticker essentially! To press vinyl to a shirt, you'd want to use only hTV (Heat Transfer Vinyl). For this product, you'd press your HTV to the HTV Anything and then adhere it to any smooth, flat surface (a cup, car window, laptop, etc.)!

A: You can certainly use it with other HTV material types. Be warned though, a few kinds such as opal and some holographics will not behave well with pressing stones over it. The stones will flick off. We don't have a product list of materials it misbehaves with but we've just experimented here and there on our own. :-)

A: Thank you very much!
We'll get that fixed.






ColorSpark HTV Anything 5ft Roll

A: Hi there! The ColorSpark HTV Anything is 12 inches wide and comes in a 5 foot roll which is 60-inches in length.

A: HTV Anything is always your back layer, it's what creates HTV into a decal with it's adhesive backing.




ColorSpark HTV Anything 5ft Roll

A: We haven't test this, but when it comes to items HTV Anything will stick to, think of your HTV Anything the way you would a sticker. If a sticker would have a tough time sticking to a surface, your HTV Anything will also have a difficult time sticking. The properties of rubber and silicone materials and the way they are made makes any adhesive difficult to stick to them.
.
.
.
.
ColorSpark HTV Anything 5ft Roll

A: Unfortunately, the only use we can approve of for this product is for pressing HTV and making decals. Sorry!

A: Hi there! We have a blog that explains all of the steps we recommend for decorating a tumbler using HTV Anything.
https://therhinestoneworld.com/how-to-make-a-rhinestone-cup

I recommend you call our call center so they can try to figure out what went wrong for you. There can be many causes for this problem, so it will be the easiest! Our number is 941-755-1696

A: HTV Anything will work with most HTV material.

A: We have exclusive coupons available if you sign up for our emails, or for first time orders. We also launch sales for most holidays!

A: Hi there! You can only print on top of vinyl that allows printing and our Siser Glitter HTV does not. Glitter HTV will press to HTV Anything to become a decal. Call us at 941-755-1696 if you have any questions.

A: Matt has used our ColorSpark Application Tape - Super High Tack Textured Glitter Black Grid to help pick up the individual letters to apply to a tumbler. But what he does more often than not is have the HTV Anything layer have a larger enough contour that the individual letters touch on that layer.

A: No.
You can just press HTV directly to fabric.
The point of HTV Anything is to create pretty HTV into a decal. The HTV Anything is sticky backed and needs to be your bottom (back) layer.

A: The ColorSpark HTV Anything can have other, thinner htv pressed to it. However, be very careful when pressing thin htv to this product as you don't want bubbles to appear. We recommend flipping the entire htv decal over and rolling the decal off of the htv carrier sheet after pressing and allowing the decal to cool a bit.

A: Unfortuntely, no, there is no way to turn Adhesive vinyl, which is basically a large sheet of sticker material, into heat transfer vinyl for shirts. Think of those stickers dentists and pediatricians give out to kids. They really don't stick to kids shirts very well but they will definitely stick to the dining table or windows when they get home. ;)

If you have several feet of Unicorn Adhesive Vinyl, I'd recommend offering to make custom names and sticker shapes for kids water bottles. We've seen many businesses make a great profit making custom decals for tumblers and waterbottles. Hope this helps!

A: I always start with the specs I use for Adhesive Vinyl or Easyweed and do a test with my Graphtec (you can click the Test Cut left arrow before sending the design to your cutter). If I'm using an older blade or if my cut strip has any grooves in it, I find that I sometimes need to slightly bump up the pressure that I use for Easyeweed.

A: Regular window decals - Permanent Adhesive vinyl.
Rhinestone decals - We have kits on site as well, but materials are ss10 hotfix, a design, magic flock, acrylic hotfix heat tape, Bling Anything, heat press.
We have thousands of youtube tutorials covering all of this as well for more in depth learning.
Bling Anything bottom layer. After brushed stones into flock, lift with hotfix tape, place on bling anything, cover with protective cover sheet, press.
The material you're inquiring under is HTV Anything, this is different.
Do not use these decals for vehicles, the uv will fade the htv very quickly.
We have kits of this as well.
Bottom layer htv anything. Apply htv. Apply rhinestones. Now it's ready to place on a tumbler, laptop, etc.

A: HTV Anything was designed to create HTV into a decal (then layer on rhinestones if you wish).
Not suitable for garments.

A: We recommend performing test cuts.
Each machine differs, even if they're the exact same machine. They're not built with extreme precision, but instead mass produced, so there's always variables that can jam up a written cut spec chart.
Blade age, machine age, belt tensions and wear, and so forth all come into play.
Helpful tip from a multi machine owner - keep a log. I like to write down each machines preferred settings once I've ran through test cuts on new materials. This saves time and money as you grow.

A: While you CAN make a decal using our HTV Anything and Siser's Easy Subli, we would not recommend it for a car decal. The sun will fade the sublimation ink fairly quickly. For making decals for tumblers, cell phones or laptops--go for it! The inks are not UV tolerant and the UV Protective sprays we've tested on other htv doesn't make them last more than a few months outdoors. Your best bet for printed outdoor decals is to outsource to someone who uses an ecosolvent printer, such as the Versacam. You can order printed decals from our site through the Estimate link under Adhesive Vinyl. :)

A: Yes, you can layer HTV glitter and press rhinestones to glitter HTV when using HTV Anything material.

A: The discount automatically applies. We did test it to be sure we did not have a glitch on the site.
You will see the big red DISCOUNT to the right on the cart page. During our Black Friday sale, you'll see both the sale discount as well as the quantity discount when you are ordering 2 or more rolls.

A: No. There are no vinyls on any market that are microwave safe.

A: Yes, you can apply ColorSpark HTV Anything to a stainless tumbler. As long as the tumbler isn't textured, you should have great results. One of our tumbler templates where we use the HTV Anything, Glitter heat transfer vinyl and hotfix rhinestones is for a stainless tumbler.

A: No, HTV Anything is to turn heat transfer vinyl into a sticker or decal. Please do not use it on apparel. These decals are great for laptops, tumblers and other smooth, hard surfaces. Since htv is not rated for continuous outdoor use, please do not use these decals for car windows, as the htv will fade in the sun.

A: We ship world wide, and shipping options vary in price by carrier. They're available to see and select from at check out.

A: You can and you'd actually have a few different options.

If you are using a sublimation tumbler, you can sub it first. Then, press your htv to the HTV Anything. After your tumbler is cool, you can apply your decal or wrap to the tumbler.

While we don't have sublimation here to test things out, you'd be able to sub your glitter htv. Then, press that to the HTV Anything.

Another option that we have not tested, but we've seen many of our TRW Crew have subbed the HTV Anything material itself! You'd need to test temperature and dwell time to get the colors you want to use dialed in properly. Then, add htv on top of the HTV Anything. Peel the paper backing and apply to your tumbler.

A: A few tips: None of our hotfix rhinestones have an application temperature of 350 degrees F--you very well may be "over cooking" the heat activated adhesive on the rhinestones. For ss06 and ss10 rhinestones, we recommend 325 degrees F for 15 seconds with medium/firm pressure. Pressing hotter or longer damages the adhesive.
Larger rhinestones require a slight temperature increase, as they have a larger profile and you need to get the heat all the way through the rhinestone to activate that adhesive.

Also, just to clarify, do not press rhinestones directly to HTV Anything. They will not stay on, as there is not a layer in the HTV Anything to secure the hotfix rhinestones. If you ever want to create wraps or decals with just hotfix rhinestones, you'll need to use our Bling Anything decal material.

The HTV Anything and glitter htv tend to hold onto heat quite a bit. Allow your wrap to cool slightly before removing the hotfix tape, so the heat-activated adhesive has a chance to re-solidify first.

We also do what we call an "insurance press", where we flip the entire wrap over and press for about 5-8 seconds from the back, to be sure the rhinestones are well adhered to the glitter htv layer.

Hope these tips help! If you are still having issues, please feel free to email our service reps at [email protected]

Thanks!

A: I'm sorry, no, we don't have any international distributors. We ship everything from our warehouse in Bradenton, FL.
Shipping is set by the different carriers and is based by the size and weight of the box needed for your items, plus the distance you live from Florida.
TRW doesn't set the shipping cost and we don't make any money on shipping.

A: As long as whatever surface you applied the ColorSpark HTV Anything to is dishwasher safe, your HTV Anything decal will be dishwasher safe.

Example: don't put your laptop with an htv anything decal on it in the dishwasher. Or if you have a tumbler that reads, "Hand wash only" on the bottom, you still need to hand wash it, although the HTV Anything decal itself would be dishwasher safe in the dishwasher.

A: Hi there!

Oh no--I'm sorry you're having issues with your decals. If the htv itself is falling off of the HTV Anything, you're not getting enough heat down to the heat-activated adhesive on the back of the htv to get a good bond.

If the HTV Anything is coming off of helmets, I'd think it's because the Brick htv is thicker, which means it's easier to get caught on impact on a helmet during an active sport.

On helmets, we typically use ColorSpark Vinyl Shield over the top of printed adhesive decals, as shown in this YouTube video at around the 6 minute mark: https://youtu.be/XpgabjPsVZE

A: Hi there and welcome to the TRW Crew!

We are the inventors of ColorSpark HTV Anything and won Best New Product of the Year when we introduced it to the crafting world.

Unfortunately, we do not have international distributors, however, we do ship our materials worldwide.

You can also use our one-time code, TRWCrew15 for 15% off of our TRW Branded materials.

Hope this information helps.

A: Hi there!
I understand what you're wanting to do, but you'd need a different material than HTV Anything. HTV Anything won't stick to fabric or textured surfaces. HTV Anything is used for smooth, hard surfaces, like tumblers or laptops. Also, HTV Anything turns heat-applied vinyl into a decal--you definitely need the heat activated adhesive of the htv to bond with the surface of the HTV Anything.

You COULD use Siser Easyweed Adhesive to press your patches to and heat apply those to cowboy hats. We've seen some great patches on trucker hats using this method. Think of the Easyweed Adhesive like a big, thin glue sheet that activates with heat. With Easyweed adhesive, you can either press a large piece to the back of your patches and trim afterwards, sealing the edges of the patch after trimming. Or if you want to cut the Easyweed Adhesive to the outside boundary of the patch, you'll mirror your design and weed out the excess material before tack pressing to the patch then peel the protective carrier sheet and press the patch to the hat.
This would be an excellent idea for us to make a tutorial video--thanks for bringing up the question!

A: HTV Anything is our Award Winning decal material, which turns heat transfer vinyl into a decal or sticker.

We've made the HTV Anything so clear and thin, you are able to press multiple types of htv to it and we've even tested plastisol transfers using it. This introductory video goes over some of the materials we've used with it and shows how the finished product turned out: https://youtu.be/sdWaEmQDJtY
Unfortunately, links in our Q&A are not clickable, so please copy and paste the link to a new browser.

We have not tested DTF with the HTV Anything, so we can't say how that would turn out. If you decide to test it, just remember a couple of things: Trim the DTF carrier close to the image before pressing and do not have the carrier touch the edge of the HTV Anything.

You also would not use any kind of app tape with HTV Anything. The HTV Anything has a strong adhesive on the back, so after pressing your htv (or testing the DTF), simply trim your decal close to the image, peel the protective cover sheet from the back of the HTV Anything and stick your decal to a smooth, hard surface.

The only time we have used app tape with the HTV Anything was when the decal we were making had elements that were not touching, so they were separate design elements and we used our app tape to hold the decal together after we peeled the HTV Anything backing sheet away. We used this to apply the name to a tumbler, then carefully removed the app tape. Since DTF uses specialty inks, it's difficult to say if the inks would be peeled up with app tape, in trying a decal like this.

A: I apologize for the conflicting answers. We don't use sublimation printers here, so we don't have a way to test it out in our warehouse.

We have a group on Facebook, named "Crafting with Rhinestones and Vinyl hosted by the TRW Crew", which has over 23,000 members. Some time after we'd created the HTV Anything, some of the members in the group started trying to sub onto HTV Anything, with wonderful results. That's when we started stating that yes, we've seen HTV Anything being subbed to.
I hope this information helps. And if you'd like to join the group on facebook, you can copy/paste this URL: https://www.facebook.com/groups/592565454142124

A: There's a few things it could be. Since it's two years old, and we're not certain of how it's been cared for it's a little hard to troubleshoot. Was it cutting fine before? Is there a carrier sheet like some of our very old materials used to have? Was it stored in heat, or a climate controlled environment? Vinyl does have a shelf life, but one of our employees also has some that's a few years old and it's still cutting fine. Have you checked your blade to see if the tip is broken, and is it an old blade? Have you checked the cutting strip on your machine to be sure it's not damaged as well, this can also hinder cutting performance.

A: There's a few things it could be. Since it's two years old, and we're not certain of how it's been cared for it's a little hard to troubleshoot. Was it cutting fine before? Is there a carrier sheet like some of our very old materials used to have? Was it stored in heat, or a climate controlled environment? Vinyl does have a shelf life, but one of our employees also has some that's a few years old and it's still cutting fine. Have you checked your blade to see if the tip is broken, and is it an old blade? Have you checked the cutting strip on your machine to be sure it's not damaged as well, this can also hinder cutting performance.

A: Vinyl shield will be more clear than the HTV Anything. You can also peel a corner of both and see which has an adhesive and that would be the shield. I like to take my labels from the rolls and place them inside the cores as soon as I get them.

A: Vinyl, one of the most widely used plastics, produces harmful fumes when burnt. Although it is an easy material to be laser-cut, laser-cutting vinyl is considered unsafe. It produces toxic chlorine gas and hydrochloric acid, which can be hazardous to the operator and also cause damage to the laser cutter.

A: Unfortunately, you cannot use adhesive vinyl with HTV Anything, because the HTV Anything has a layer that bonds to the HTV when it is pressed.
However--we have a different awesome product that you can use with Adhesive vinyl to protect it. Our ColorSpark Vinyl Shield is a clear, mask-like material that goes over the top of your adhesive vinyl, which protects the vinyl from scratches, lifting and even the dishwasher. The ColorSpark Vinyl Shield also has a UV protectant built in, to help keep your decals from fading in the sun.

A: The total due for any orders placed is shown in your cart at checkout and on the invoice emailed to you after you complete checkout. Your credit card or bank account determine when they post the charge to your account.

A: ColorSpark Bling Anything and HTV Anything are very similar in that they turn heat applied materials into a decal, sticker or tumbler wrap. The key to knowing which to use is in the name of the product. If you are pressing Rhinestones Only (bling) then use Bling Anything. It is the only product that can turn hotfix rhinestones into a decal.
If you are using htv as the first thing that you press to these materials, technically, you could use either, but we created HTV Anything to turn htv into the decals or wraps. HTV Anything is thinner than Bling Anything, so you can actually press thinner htv to it and get good results.
Being able to break the typical pressing 'rules' and layer glitter on top of glitter or rhinestones on top of glitter is just one of the benefits to using these materials.

A: Nothing comes to mind that will stick to silicone. Even silicone that's had epoxy on it, will still not stick and pop right off. You may have a little luck sanding only the area that it will be applied to give it some grip, but we still can't guarantee it will cooperate with silicone.

A: The decals made with ColorSpark HTV Anything are meant to go on smooth, hard surfaces with no flex to the surface. Think of the decals the way you would a regular sticker. If a regular sticker would not stick to the surface, a decal made with HTV Anything will not stick.

A: We ship worldwide. You can add the HTV Anything to your cart and continue to checkout. You'll have different options for shipping at checkout.

A: Hi there!
Yes, definitely. We ship worldwide.

A: Depends on if you're figuring in your shipping etc as well.
This online calculator from Google says without shipping it's $0.04
Here's the link: https://www.calculatorpro.com/calculator/cost-per-square-inch-calculator/

A: Hi there! We pulled up your order to check which materials were ordered. You'd only ordered one roll of HTV Anything. The other roll of white material that you'd ordered is the 15 feet of Acrylic Hotfix transfer tape. The textured white backing is the easiest way to identify it. This tape is heat resistant and used to lift the rhinestones from the blue Magic Flock template.
As for the HTV Anything wrap, the tumbler you put it on needs to be smooth and not textured. We've also found adding a thin bead of Supertite Adhesives Fusion Tack glue under the seam, then securing the tumbler and wrap with pony-O's overnight while the glue cures has been incredibly helpful in securing the wrap and the seams.

A: We, and our materials, are based in Florida, USA, but we ship worldwide!

A: We can't commit to if it were safe or not as it's not intended for that use and we haven't tested that. Also keep in mind skin irritation and allergies with various people.
If you were to try to body wear the material, it would act like regular adhesive vinyl. The adhesive is meant for smooth clean surfaces that stay smooth and clean. I would gather that these would fall off in minutes between moving and or any sweat or skin oils making the adhesive fail.

A: Unfortunately we cannot control shipping costs. We're based out of Florida, USA and currently do not have other warehouses overseas.

A: Hi there! Can we ask which browser you are using? The site doesn't work well with Firefox, if that may be the issue.

For Heat Transfer Vinyl, we offer several different types: Siser Easyweed - a bit shinier than other htv. But it's not faux pleather shiny. We also have glitters that may be of interest to you. The ColorSpark Reflective Glitter and Siser Twinkle both are reflective glitters which are smooth to touch--with a glossy finish and light up with ambient light. These woul be the most shiny htv's we'd offer. If you have other questions, please feel free to email us at [email protected] or reach out to us on social media.

A: Our ColorSpark HTV Anything turns heat applied vinyl into a decal or wrap. It works best on smooth, hard surfaces. We have successfully used HTV Anything on both Glass and Stainless Steel tumblers and glasses.

Be sure to clean the surface with an alcohol wipe before applying the decal or wrap. When we make tumbler wraps, we add a bead of Supertite Adhesives Fusion Tack under the seams and secure with ponytail holders until the adhesive cures. This ensures the wrap doesn't lift with use.

A: HTV Anything is meant for smooth, hard surfaces. We have not tested our HTV Anything decals on wood, but it does not seem that a decal would adhere well on wood.

A: Hi there!

While the HTV Anything would be able to weather the elements, heat transfer vinyl itself is not rated for continuous outdoor use and the htv will fade.

We used to use glitter htv and HTV Anything for decals, but with how quickly htv fades in the sun, we've stepped away from creating these types of decals.

A: Great question!
If you experiment a touch, any htv will work. The issue is thinner htv will bubble since it doesn't have that "breathe through" that fabric gives it with being pressed to HTV Anything. So you'll need to adjust your time / pressure / temp a touch to find that sweet spot for the thinner htv to better cooperate. This is often why in our videos and live trainings you'll see us use glitter htv as it's thicker. We prefer glitter, but with a lighter hand other htv will work as well.

A: Yes, the HTV Anything is dishwasher safe and no, you do not need to seal decals or wraps made with htv and HTV Anything.

A: You can make window decals using HTV and HTV Anything, however since htv is not rated or created for continuous UV exposure, the htv will start to fade quickly in the sun.

A: There is also an option for a 3 foot roll here:
https://www.therhinestoneworld.com/colorspark-htv-anything-3ft

A: At the checkout screen there is an option to input card information.

A: Per our sitewide sale, our rolls of HTV Anything are automatically discounted in your cart. "Special deal: extra 40% off discount auto-applies at checkout!"
This means no coupon code is required. If you compare the price of the HTV Anything on our site to the price in your cart, you'll see that it is a lower price in your cart for this sale.