Products (Total Items: 20)
Sort by:
Instant Download Free Shipping
$29.99
Available In Stock
$29.90
Available In Stock
Cutting Mat 12 by 24 inches is a lightly frosted, flexible clear plastic with a 1 inch grid and ruler. This mat offers a standard tackiness and a 12 by 24 inch cutting area. The purpose of a cutting mat is to hold your material firmly in place while it is being run through your cutting machine. The thinner the material being cut, the less tacky the mat should be to avoid tearing. A cutting mat is always needed to cut scrap material. When the vinyl is not its full, original width, the mat allows the vinyl to feed into the machine properly. This is NOT a self-healing mat intended to be used with x-acto knives or rotary cutters. It is intended for cutting Adhesive Vinyl or Heat Transfer Vinyl with a Vinyl Cutter. This Cutting Mat 12 by 24 inches is compatible with the full size GCC Puma IV Cutter, GCC Expert II LX Cutter, GC Expert II Cutter, GCC Jaguar V Cutter and Graphtec CE7000 Cutter.
$15.99
Available In-Stock
Cutting Mat 12 by 12 inches is a lightly frosted, flexible clear plastic with a 1 inch grid and ruler. This mat offers a standard tackiness and a 12 by 12 inch cutting area. The purpose of a cutting mat is to hold your material firmly in place while it is being run through your cutting machine. The thinner the material being cut, the less tacky the mat should be to avoid tearing. If you need a lighter tack option, check out the Silhouette Cameo 12 inch Cutting Mat. A cutting mat is always needed to cut scrap material. When the vinyl is not its full, original width, the mat allows the vinyl to feed into the machine properly. This is NOT a self-healing mat intended to be used with x-acto knives or rotary cutters. It is intended for cutting Adhesive Vinyl or Heat Transfer Vinyl with a Vinyl Cutter. This mat is compatible with the full size Cricut and Silhouette Cameo Cutters.
$11.99
Available In-Stock
Keep your blades secure with TRW CAMEO/Graphtec Blade Holder. This blade holder is compatible with the Cameo and Graphtec cutters sold on our site. Replace your blade holder at a fraction of the cost of name brand, with the TRW version!
$16.95
Available In Stock
Ready for a blade replacement? Craft Vinyl Cutter replacement blade for Roland|GCC|Cricut Cutter Blade - 45 Degrees 2mm is a replacement blade for the following cutters: Roland GS-24, GCC Expert IV, GCC Expert, Cricut Maker, Cricut Explore Air and Cricut Explore Air 2. This blade is not compatible with Cricut Joy. If you are cutting thinner materials such as Siser-Easyweed or Colorspark-Holographic we suggest you use the 45 degree blade. If you are cutting thicker material like Magic-Flock or Glitter-vinyl, we suggest the 65 degree blade for the best cut. 2mm blades fit into the standard blade housing of the Roland GS-24, Cricut Explore Air, Cricut Explore Air 2, older GCC models (Jaguar IV and Expert 24), and TRW's Blade Holder. For Cricut Maker, Cricut Explore Air and Cricut Explore Air 2 you must use the pre-existing holder that came with your Cricut to hold the TRW replacement blade. To fit into the standard blade housing for the Jaguar V and Expert II you will need the The 2.5mm blade, this 2mm blade will not fit in their standard blade housing.
$15.95
Temporarily Out of Stock - Check back soon!
Ready for a blade replacement? This is a 45 degree replacement blade for the following cutters: GCC Jaguar V, Puma IV and Expert II cutters. The 2.5mm blade will fit into the standard blade housing for the GCC Jaguar V, Puma IV and Expert II. If you are cutting thinner materials such as Siser-Easyweed or Colorspark-Holographic we suggest you use the 45 degree blade. If you are cutting thicker material like Magic-Flock or Glitter-vinyl, we suggest the 65 degree blade for the best cut. To fit into the standard blade housing of the Roland GS-24, Cricut Explore Air, Cricut Explore Air 2, older GCC models (Jaguar IV and Expert 24), and TRW's Blade Holder you will need the 2mm blade, this 2.5 mm blade will not fit in their standard blade housing.
$14.95
Temporarily Out of Stock - Check back soon!
Ready for a blade replacement? This is a 65 degree replacement blade for the following cutters: GCC Jaguar V, Puma IV and Expert II cutters. The 2.5mm blade will fit into the standard blade housing for the GCC Jaguar V, Puma IV and Expert II. If you are cutting thinner materials such as Siser-Easyweed or Colorspark-Holographic we suggest you use the 45 degree blade. If you are cutting thicker material like Magic-Flock or Glitter-vinyl, we suggest the 65 degree blade for the best cut. To fit into the standard blade housing of the Roland GS-24, Cricut Explore Air, Cricut Explore Air 2, older GCC models (Jaguar IV and Expert 24), and TRW's Blade Holder you will need the 2mm blade, this 2.5 mm blade will not fit in their standard blade housing.
$14.95
Available In Stock
Ready for a blade replacement? Craft Vinyl Cutter replacement blades for Roland|GCC|Cricut Explore Cutter Blade - 65 Degrees 2mm is a replacement blade for the following cutters: Roland GS-24, GCC Expert IV, GCC Expert, Cricut Maker, Cricut Explore Air and Cricut Explore Air 2. This blade is not compatible with Cricut Joy. If you are cutting thinner materials such as Siser-Easyweed or Colorspark-Holographic we suggest you use the 45 degree blade. If you are cutting thicker material like Magic-Flock or Glitter-vinyl, we suggest the 65 degree blade for the best cut. 2mm blades fit into the standard blade housing of the Roland GS-24, Cricut Explore Air, Cricut Explore Air 2, older GCC models (Jaguar IV and Expert 24), and TRW's Blade Holder. For Cricut Maker, Cricut Explore Air and Cricut Explore Air 2 you must use the pre-existing holder that came with your Cricut to hold the TRW replacement blade.To fit into the standard blade housing for the Jaguar V and Expert II you will need the The 2.5mm blade, this 2mm blade will not fit in their standard blade housing.
$14.95
Available In Stock
Craft Vinyl Replace your blade on your cutter with this Graphtec Cutter Blade - 45 Degrees. This blade is a 45 degree replacement for Graphtec Machine Cutters. The blade will fit into the standard blade housing for Graphtec Cutters. If you are cutting thicker material like Magic-Flock or Glitter-Vinyl, we suggest the 60 degree blade for the best cut. Cutter replacement blades for Graphtec Cutter Blades - 45 Degree AGTK
$17.95
Available In Stock
Replace the blade on your cutter with this Graphtec Cutter Blade - 60 Degrees. This blade is a 60 degree replacement for Graphtec Machine Cutters. The blade will fit into the standard blade housing for Graphtec Cutters. If you are cutting thinner materials such as Siser-Easyweed or ColorSpark-Holographic, we suggest the 45 degree blade for the best cut.
$17.95
Temporarily Out of Stock - Check back soon!
Heat Press Pillows also known as heat transfer pillows or heat printing pillows are non-stick foam inserts used with Heat-Presses during the heat printing process. Heat press pillows are recommended when pressing a garment with zippers, buttons, snaps, collars or thick seams. When used, raised elements of the garment sink down into the pillow, eliminating pressure points and creating a more even pressing surface. Without the Heat Press Pillow, the heating element is unable to make a tight, smooth seal on the Heat-Transfer-Vinyl. They also eliminate any indentation that can appear from the heat press outside edges. To use, place the pillow inside or underneath the garment, adjust your heat press using the knob atop the upper platen to accommodate the new thicker pressing surface and begin pressing. Heat press pillows are reusable. This pillow is 5.5 inches by 22 inches and 6mm thick. It also is available in a 12-by-14-square size and a 5.5-by-5.5-square size. Improve the final result of vinyl applications to backpacks, hats, hoodies, reversible mesh jerseys, baby onesies, and any garment with raised surfaces, using a Heat Press Pillow. Do I need a Heat Press Pillow or Protective-Cover-Sheet? If your garment has raised surfaces like zippers, buttons, or thick seams, you will need a Heat-Press-Pillow to ensure equal pressure when applying Heat-Transfer-Vinyl. If your garment does not have raised surfaces, but you will be creating a multilayered Heat-Transfer-Vinyl design or adding Hot-Fix-Rhinestones on top of vinyl, you will need a Protective-Cover-Sheet.
$19.95
Available In Stock
Heat Press Pillows also known as heat transfer pillows or heat printing pillows are non-stick foam inserts used with Heat-Presses during the heat printing process. Heat press pillows are recommended when pressing a garment with zippers, buttons, snaps, collars or thick seams. When used, raised elements of the garment sink down into the pillow, eliminating pressure points and creating a more even pressing surface. Without the Heat Press Pillow, the heating element is unable to make a tight, smooth seal on the Heat-Transfer-Vinyl. They also eliminate any indentation that can appear from the heat press outside edges. To use, place the pillow inside or underneath the garment, adjust your heat press using the knob atop the upper platen to accommodate the new thicker pressing surface and begin pressing. Heat press pillows are reusable. This pillow is 12 inches by 14 inches and 6mm thick. It also is available in a 5.5-by-22-rectangle size and a 5.5-by-5.5-square size. Improve the final result of vinyl applications to backpacks, hats, hoodies, reversible mesh jerseys, baby onesies, and any garment with raised surfaces, using a Heat Press Pillow. Do I need a Heat Press Pillow or Protective-Cover-Sheet? If your garment has raised surfaces like zippers, buttons, or thick seams, you will need a Heat-Press-Pillow to ensure equal pressure when applying Heat-Transfer-Vinyl. If your garment does not have raised surfaces, but you will be creating a multilayered Heat-Transfer-Vinyl design or adding Hot-Fix-Rhinestones on top of vinyl, you will need a Protective-Cover-Sheet.
$19.95
Available In Stock
Heat Press Pillows also known as heat transfer pillows or heat printing pillows are non-stick foam inserts used with Heat-Presses during the heat printing process. Heat press pillows are recommended when pressing a garment with zippers, buttons, snaps, collars or thick seams. When used, raised elements of the garment sink down into the pillow, eliminating pressure points and creating a more even pressing surface. Without the Heat Press Pillow, the heating element is unable to make a tight, smooth seal on the Heat-Transfer-Vinyl. They also eliminate any indentation that can appear from the heat press outside edges. To use, place the pillow inside or underneath the garment, adjust your heat press using the knob atop the upper platen to accommodate the new thicker pressing surface and begin pressing. Heat press pillows are reusable. This pillow is 5.5 inches by 5.5 inches and 6mm thick. It also is available in a 5.5-by-22-rectangle size and a 12-by-14-square size. Improve the final result of vinyl applications to backpacks, hats, hoodies, reversible mesh jerseys, baby onesies, and any garment with raised surfaces, using a Heat Press Pillow. Do I need a Heat Press Pillow or Protective-Cover-Sheet? If your garment has raised surfaces like zippers, buttons, or thick seams, you will need a Heat-Press-Pillow to ensure equal pressure when applying Heat-Transfer-Vinyl. If your garment does not have raised surfaces, but you will be creating a multilayered Heat-Transfer-Vinyl design or adding Hot-Fix-Rhinestones on top of vinyl, you will need a Protective-Cover-Sheet.
$11.95
Available In Stock
Protective Cover Sheet also known as Teflon sheets or non-stick sheets, act as a barrier between the heat element and the garment during the heat printing process. Protective Cover Sheets are commonly used with Heat Presses when transferring designs to ensure a smooth, semi-gloss finish on graphics. When layering Heat Transfer Vinyl or adding Hotfix Rhinestones Rhinestones to a design, place the cover sheet on top of your garment before using the heat press to protect the first layer. When printing the front and back of a shirt, place the protective sheet cover between the fabric to prevent the shirt from sticking together. Protective Cover Sheets are reusable. They will only need to be replaced if they become ripped, creased or wrinkled to the point of ineffectiveness. This protective sheet is 18 inches by 20 inches. If you need a smaller sheet check out the 9.75 by 9.75 cover sheet.
$16.95
Available In Stock
Protective Cover Sheet also known as Teflon sheets or non-stick sheets, act as a barrier between the heat element and the garment during the heat printing process. Protective Cover Sheets are commonly used with Heat Presses when transferring designs to ensure a smooth, semi-gloss finish on graphics. When layering Heat Transfer Vinyl or adding Hotfix Rhinestones Rhinestones to a design, place the cover sheet on top of your garment before using the heat press to protect the first layer. When printing the front and back of a shirt, place the protective sheet cover between the fabric to prevent the shirt from sticking together. Protective Cover Sheets are reusable. They will only need to be replaced if they become ripped, creased or wrinkled to the point of ineffectiveness. This protective sheet is 9.75 by 9.75 inches. If you need a smaller sheet check out the 18 inches by 20 cover sheet.
$6.95
Available In Stock
Magic Heat Tape also known as heat-resistant tape, high temp tape, thermal tape, or polyester film tape, prevents heat press designs from shifting during the pressing process. Magic Heat Tape is ½ inch wide and 216 feet long. It easily peels off with the vinyl’s backing after the design has been pressed. The purpose of Magic Heat Tape is to hold transfers in place during application. It won’t leave a residue or melt into your garments. This semi-transparent tape works wonders on multilayer, multicolored or oversized designs to prevent them from shifting. Magic Heat Tape is ideal to use with Heat-Transfer-Vinyl, Rhinestone-Hot-Fix-Transfer-Tape, and Hot-Fix-Rhinestones on a Heat-Press-Machine.
$11.99
Available In Stock
$24.99
Available In Stock
Secure your GCC or Roland blade with the TRW Blade Holder! This blade holder is compatible with all GCC Vinyl Cutters, with the exception of the Expert II. The TRW GCC / Roland blade holder is a afforable alternative to name brand blade holders. Blade Holder for GCC/Roland Cutters (2mm)
$44.99
Available In Stock